DIY Mobile Island/Grill Cart

rolling kitchen island

how to build a custom kitchen island

May means that the unofficial start of summer is near! I don’t know about you, but when I think about the summer I am reminded of warmer weather, tank tops, and most importantly, grilling season! To help kick off the start of BBQ season, I partnered with my amazing friends at Bernzomatic to create a mobile kitchen island and grill cart! Best part, I have the FREE plans for you right here!

grill cart
One of the things I love about this project is that it is multi-functional! It can be used as a grill cart in the summer, and then stored in the kitchen as a mobile island in the winter! Even better, Memorial Day means that Father’s Day is around the corner, and this bad boy would totally double as a mean Dad’s Day gift (you’re welcome)!

Ready to get started? If you’d like to skip the step-by-step, you can also download the free printable plans by clicking here! Otherwise, here we go!

What You’ll Need:

bernzomatic torch
Tools
Bernzomatic TS4000
Miter Saw/Circular Saw
Pocket Hole Jig & Bits (Optional)
Drill
Table Saw (Optional)
Sander/Sanding Block
Paint Brush
Carpenter’s Square
Measuring Tape
Safety Goggles
Heat Resistant Gloves

Materials
(8) 2 x 2 x 8′ Boards
(4) 1 x 6 x 8′ Boards
(1) ½ Sheet of ½” Birch Plywood
2 ½” Wood Screws
2 ½” Pocket Hole Screws
1″ Pocket Hole Screws
Mineral Oil
Paint*
(*I used Blue Charcoal from BEHR)
Wood Glue

Accessories
(4) 3 ½” Metal Castors
(3) Wire Baskets
Towel Rack
Metal Hooks

The Steps:

To help make this build more manageable, I am going to walk you through each section of this build in parts (i.e., cut list, frame, panels, shelves). You’ve got this!

Cut List:

For this project you will need the following pieces:

2 x 2’s:
(4) Legs @ 31”
(6) Long Frames @ 39”
(6) Short Frames @ 17”
(6) Basket Slats @ 17”
(4) Supports @ 17”
(2) Basket Dividers @ 8 ½”
(4) Spacers @ 2″ (for castors)

Plywood:
(2) Side Panels @ 8 ½ x 17”*
(1) Back Panel @ 8 ½ x 39”*

(*if you do not have a pocket hole jig, please see the “Panel” section of this build before cutting your plywood panels)

1 x 6’s:
(4) Top Shelves @ 44” Long
(4) Bottom Shelves @ 42” Long*

(*Optional: rip/cut ¼” off the width of each bottom shelf board with table saw to avoid having an overhang on the bottom shelf)

Part I: The Frame

1. Cut your 2×2’s into the dimensions listed in the cut list. Make sure to label each piece so that nothing gets misplaced!

how to label wood pieces

2. Drill pocket holes in the ends of every single 2 x 2 board (with the exception of the legs – don’t drill any holes in the legs). If you do not have a pocket hole jig, you can skip this step and just use wood screws to join your pieces together in the next few steps.

how to join wood

3. Begin assembling your side frames by attaching 2 small frame pieces to 2 leg pieces at a time. Your small frame pieces will attach to the very top and very bottom of your legs to create a giant rectangle. All four corners of your panel should look like this:

diy grill cart

4. Once both of your side frames are assembled, and you have two large rectangles, add the last 2 short frames to the inside of the rectangles to create the shelf. You can use the 8 ½” basket divider pieces here to help with spacing.

how to build a grill cart

how to use spacers on wood

5. Once your side panels are complete, it’s time to add the long frame pieces. Just line them up to the short frame pieces and attach them directly to the legs. This will create the entire frame for your mobile cart.

how to square wood when joining

6. When your frame is complete, you will essentially just have a giant box! So, now it’s time to add the basket dividers. Use a square to measure where they belong. My baskets were just shy of 12″ wide, So I added my shelf frames by measuring 12″ inward from the legs and then screwed them into the frame with pocket hole screws.

how to use a wood square

how to level wood

7. Once your shelf dividers have been installed, you can go ahead and install the shelf support pieces to the bottom and top of the piece (2 on top, and 2 on the bottom) with screws and wood glue.

how to build mobile storage

how to build a kitchen cart

8. At this point, you can install your (6) basket slats as well! I installed mine in between each shelf space at 11″ apart (that just means I didn’t line them up with the basket frame pieces, I just installed them ½” in from each so that the basket doesn’t fall through the opening). It looks like this when it’s finished later (I installed mine last, but they can be installed now):

how to build custom grill cart

9. Keep your (4) wood spacers for last. You won’t attach those until later. But, for now, do a happy dance, because your cart’s frame is complete!

The Panels:

1. Use a circular saw or table saw to rip your plywood to the dimensions in the cut list above (if you don’t have a table saw, you can also ask your local hardware store to cut these pieces for you). Once that’s done, use your pocket hole jig to drill pocket holes in your panels*.

*If you don’t have a pocket hole jig, you can cut grooves into your upper frame pieces prior to assembling, or attach the plywood to the inside of your cart using wood glue and brad nails. If you do either of these, please make sure to cut your plywood panels a bit taller and/or longer to account for the added square footage.

memorial day weekend grill cart

2. Attach your plywood panels to your cart. The panels will be installed on the upper portion only.

how to build a grill cart

3. Use wood putty to hide any unwanted pocket holes or imperfections in the wood.

how to patch wood

4. At this point, give the entire piece a good sanding!

how to sand wood

5. And, if you’re choosing to paint the cart’s frame, you can do for it here following the sanding!

how to customize kitchen island

… don’t forget to paint the spacer pieces we left out earlier!

The Shelves:

1. Cut your 1 x 6″ shelf pieces as per the cut list above. Your 4 bottom shelf pieces will be shorter than the top pieces because you will want them to be flush with the frame of the cart. You may also want to rip these pieces down by ½” of an inch to help keep them from spilling over the sides of the cart.

how to custom cut butcher block top

2. Because your bottom shelves will be fit to size, you will need to cut out small notches in your front and back pieces to hug the legs. You can do this by using your spacers to trace how thick the legs are and then cut the notches out using a jig saw or bandsaw.

how to build a custom storage cart

how to make a rolling storage cart

how to build custom cart

3. Once your pieces are cut, use your Bernzomatic TS4000 to torch the pieces. Make sure to torch both sides to prevent cupping!

how to wood burn

how to torch wood

4. After torching, attach your boards by screwing them into the 2×2 supports with 2 ½” wood screws. You can hide the screws by attaching the boards from underneath.

free woodworking plans grill cart

I used quarters to help space out my bottom pieces (since I trimmed them all down by ½” each). This spacing allows for easier clean up if crumbs fall to the bottom of the cart!

diy grill cart

5. Next, attach your spacers to the bottom corners of the cart. These are here to help attach your castors!

how to build a grill cart

6. Once your top and bottom are attached, flip the cart back over and attach your castors.

how to add castors to kitchen island

7. Now, go ahead and flip your cart over and attach the rest of your accessories (i.e., towel rack and hooks).

how to install hooks on kitchen island

8. Last, use mineral oil to seal your shelves. Using mineral oil helps to make the surface food-safe!

how to torch wood

Now, celebrate your build with an epic Memorial Day Weekend Party!

rolling kitchen island

One of my favorite things about this cooking cart is that it has storage to house other grilling essentials, such as my citronella candles for keeping unwanted guests away, my Bernzomatic Utility Lighter, and Bernzomatic Detail Torch (which, we use for roasting)!

kitchen island with storage

how to roast peppers with torch

 What do you think? Have I convinced you that you need your very own mobile kitchen island/grill cart?

grill cart

bernzomatic bbq torch

If you want to Pin This for later, you can save the image below (which also leads to my FREE printable plans for this project)!

In the meantime, make sure to check out Bernzomatic’s Summer Entertainment Guide for more awesome project ideas!

This post is sponsored by Bernzomatic. While compensation has been received for this post, all design ideas, product opinions, and resin color choices are my own. For my full disclosure policy, click here.

This post may contain affiliate linking. While these links cost no extra for you to use, a percentage of all sales made through these links will help fund future DIY Huntress projects. For more information, please visit my "About Me" page. Thank you!

OTHER PROJECTS YOU MAY ALSO LIKE

1 comment

Leave a Reply

Your email address will not be published. Required fields are marked *